Endura Flap™ Door Mount Congratulations on your purchase of one of the finest pet doors made, featuring the exclusive Endura Flap™. Installation Instructions For Single and Double Flap Models PARTS LIST For single flap door mounts 1 flap frame • 1 trim frame 4x 1-3/4 inch screws • 4x 2-1/4 inch screws For double flap door mounts 2 flap frames • 4 tunnel pieces • 1 tube of silicone 4x 2-1/4 inch screws • 4x 2-3/4 inch screws For both single and double flap door mounts: 1 installation template • 8 hole plugs 2 weather-strips • 1 warranty card TOOLS REQUIRED Pencil Drill with 3/8 inch drill bit Level Jigsaw or reciprocating saw Phillips head screwdriver Please read instructions thoroughly before beginning installation. Instructions 1. Pet Door Guys In Glass Dog Door is a glass replacement for your current French or sliding glass door with Endura Flap pet door installed PET DOOR GUYS ORDER FORM Replacement window with built in doggy door fits French and sliding glass. Have you ever wished you could have a pet door installed right into your glass patio door? This uniquely designed in-glass pet door creates a clean look that compliments your sliding glass patio or french door without the hassle of full height door inserts that block your doorway and don't seal properly. ![]() Tape the provided template to the door. The top edge of the cut-out line should be 1-1/4 inch (or more) above the dog’s withers (shoulders) for the single flap door mount, and 2 inches for the double flap door mount. Be careful not to unduly reduce the strength of the door by cutting too close to the bottom of the door. Mark the hole centers for the four holes and remove the template. Drill the four 3/8 inch holes. Note Drill bit needs to be long enough to go through the interior and exterior of the door. Centos 7 firewall turn off. It should be both level and straight when making the holes to ensure the two frames will align properly. ![]() Cut along the line as shown in Figure 3. Note Jigsaw needs to be level and straight when cutting the lines to ensure the two frames will align properly. Install the weather-stripping into the groove on both frames with the start /end gap at the bottom. If a single flap door mount, place the pet door trim frame on the outside of the door and the flap frame on the inside and skip to Step 14. If a double flap door mount, assemble the four-piece tunnel by first bending the screw tabs down as shown in Figure 4 in the top and bottom tunnel pieces (the two identical shorter pieces). Note Only bend the tabs once, bending more than once may result in the tabs breaking off. Figure 5: Remove the four flap assembly screws 9. Remove the screws in the four corners of the flap frame assembly as shown in Figure 5. Place the top piece on, with the bent tabs down and align the top piece so the holes in the tabs lines up with the screw holes in the flap frame and screw in as shown in Figure 6. Repeat for the bottom piece. Slide in the tunnel side pieces as shown in Figure 7. Bend the tabs down with your thumb or a screwdriver handle. How to activate any software using cmd advanced commands. ![]() Place the flap frame with the tunnel attached on the inside and the other flap frame outside. Select the 2-1/4 inch set of screws for 1-3 /4 inch doors and the shorter set for 1-3/8 inch doors. Insert these into the pet door from the inside. For doors with a thickness of less than 1-3/8 inch, see special instructions. For doors between 1-3/4 inch and 2-1/4 inch with the double flap door mount, use the 2-3 /4 inch screws. Start all four screws as shown in Figure 8, but do not tighten. Before tightening down the screws, check that the pet door is level and adjust as needed. Tighten the screws until the weather-stripping compresses and the pet door touches the door. Do not over tighten. Hammer the hole covers into the frame using the wooden end of a hammer (or similar non metal tool). Patio Doors With Pet Door Installed![]() For double flap door mounts, apply silicone along the inside of the tunnel where it mates with the flap frames to seal your pet door from the elements. Failure to seal your pet door can lead to severe water damage. For expert installation help, replacement flaps and parts or other quality pet door products, visit PetDoors.com or call 800-826-2871 (Press 2) Monday – Friday 7:00 a.m. PST Endura Flap™| U.S. 7,814,956| Pat. Description In 2001 Patio Pacific set out to design and build the best pet door flap ever made. We’ve released the resulting flap in a version designed for all solid core, hollow core, metal or storm doors: The award winning Patio Pacific Endura Flap™ Pet Door for Doors. If you’ve never owned a pet door before, you’re going to be very satisfied. It does what you think it should. Doors With Pet Doors Already InstalledBut if you have ever owned a pet door, hold on to your socks -you’re not going to believe how much better this is than what you’ve had in the past. Take a look at the Endura flap Pet Door Information that we’ve provided, and you’ll begin to see what we’re so proud of! A note on single versus double flap versions. Features Extreme performance Endura Flap™ We get it, you’re tired of replacing worn out, leaking flaps. You owe it to yourself to investigate the Endura Flap, the best, most highly engineered pet door flap ever made. It seals, it insulates and it will last forever! Patio Doors With Pet Door InstalledBy the way, want to see what happens over time to the more traditional vinyl flaps? See our Leaky Flap page! High aspect ratio design Much easier to fit your pet. Improves security for medium to large sized pets. Easier to share with a smaller pet.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |